Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
We have noticed this article about Tools You Need to Install a New Bathtub down the page on the web and figured it made perfect sense to talk about it with you in this article.
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging job. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall surface to remove the old tub and place the brand-new tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. Ensure you have certified on your own for the task and fit attempting it. Instead of working with a service provider to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will assist you install a new bathtub in your bathroom if you have actually currently purchased a brand-new tub and don't require to change the plan of your previous water pipes.
Your tools and product checklist ought to consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be rather problematic as a result of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will come from the pipes. When the supply pipes have been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before proceeding to fit the new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in position with the supplier offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type ought to be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the called for setting. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub till the level checks out degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the water as well as inspect all joints as well as new pipework for leaks and tighten them if essential. Fill up the bathtub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub should wait until the bathtub has been utilized a minimum of when as this will resolve it right into its last setting.
Planning for the Setup
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and installations. They are offered in tubes and cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can break relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly offered on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that article on How to Install a Bathtub Yourself when doing a lookup on the web. If you enjoyed our blog entry if you please don't forget to share it. Many thanks for your time. Please come visit our blog back soon.
Maintenance Sign-Up Report this page